TRUMP KUATO LIVES
The new Regan Fuzz with artwork by Alex Fine Illustration.
3 knob controls (volume, tone, gain) allow you to dial in everything from a dirty boost, to distortion, to thick fuzz!
The Reagan fuzz is based of the “Civil War” Version of the big muff.
It has all the classic sound but with with some modern upgrades. Including new components, 9v plug (standard 2.1mm), and true bypass switching.
Original illustration by Baltimore based artist Alex Fine.
This is the Ampeg V-7 Guitar Amplifier. The footswitch is a powered three channel XLR 5 Pin Configuration. On the Main Board of the V-7 it controls what the switches modify. Located at the bottom of the schematic you will see where I labeled the 5 Pin XLR. Most of the time I wire my pedal to only have one button, for distortion. This unit above has the reverb and channel 1 as kick switches, pedal should be securely mounted to kick “ON” function.
V design with double Classic Cry Baby Wah. The Wah on the left has been modified to incorporate a front facing “kick on” switch. It engages a Dunlop Power Booster that has been inserted into the shell. Volume to boost is on the bottom left of pedal. Stereo chain from distortion to out through. The custom pedal on the left is a 5pin xlr input box for controlling an Ampeg V-7 (CH1, CH2 & Reverb). This box has been simplified for head distortion control only. The version with all three uses the same box but has 2 buttons on top pan L/R & 1 “front kick” placement switch. (From L to R) V7 controller, Digital Reverb RV-7, Digital Delay DD-3, Digital Metal MZ-2, Dunlop Cry Baby X2, Power Pad II, Phase Shifter PH-3, Flanger BF-2, Chromatic Tuner TU-2 on .5″ Plywood Custom Board.
Pedal Board shapes should vary based on your live performances and comfortable stance. Try to think about where the microphone stand would sit if you play effects and sing. From those ideas sketch out your shape on a blank board and cut/paint/finish.
So when your ready to create a pedal board there are a few things you need to keep in mind. First you want to be able to get the correct tones and effects for what you are trying to create. It is best to set up your pedals on the floor loose and determine each placement in the chain as well as whether or not you even like what it has to offer. Once that is figured out you will need the following items.
A large piece of 1/2″ quality plywood, spray paint, drywall screws of different lengths, a drill, a reciprocating saw, all the required cabling and a good power supply. Lay out your pedals not wired on top of the plywood. Create the most comfortable layout so that you can press on them without hitting another pedal by accident. I typically place my pedals a 1/2 a foot length spacing apart. this way if I was to press in the center point of that spacing I could engage two pedals at the same time. this technique only really works well for pedals like boss style because there is not a small button switch you have to engage. After you layout is complete then carefully trace in pencil around the outer edges of each placed item. then draw an x on the left and right side of the pedal where you will send you zip tie through. make sure that it will not interfere with the inputs and outputs. draw your outer perimeter of where to trip as well as a handle option. once you have that done remove all items from the board. spray paint your board. using you drill create 1/4″ holes on the x marks. return your pedals to the board and zip tie them all in place. next wire up your entire board. then using the screws you will attach them around each pedal, on a slight angle away from the pedals to secure each on firmly in place.
This one is very unique. I tried to make a dual unit with the smallest footprint possible. If you put the backs together they can attach for portable carry. this one is a an Arion built with Arion original power supplies. As you can see I did a similar layout with the plywood, placed my pedals for spacing and functionality and then drew my outlines and cut lines. below also are finished product views.
1/2″ plywood, the pedals don’t ever budge and it don’t slide on wood floors…(trick) Take a few 1-1/2″ drywall or wood screws and place them left and right of your center wood. Screw them through until you feel them pierce out 1/8″, Done. no one will see it at a show but those little guys will dig in and prevent your board from pushing around.
I created this simple mod to easily use all of the functionality of this great stereo looper pedal Ditto. I found that fat footswitches improve accuracy and help simplify control.
I wired this unit using a 5 pin din connection. Now a standard midi cable will make the connection at any length needed. Disassemble the unit and prepare the wire connection. You will need 2 wires from the footswitch and 3 wires from the toggle switch.
Run the wires to the battery compartment. There is enough room here to mount a female 5 pin din connection. I separated the two switches to have all there channels on separate plugs. Cut all terminals to half length.
The footswitch is a metal can USB design. I removed the circuit board and wires and used the limit switches inside the pedals to operate at normally open. When they press it will close the circuit to engage the switch function on the Ditto. The Black cable pin 1 to the footswitch was used as common and jumped between pedal Store & Backing Track. The controls on the Ditto still function normally. Female 5 pin din mounts on the inside and screws fasten from the outside.